View AN2720S_263619.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

EZ-Link (AN2720SC)
Single-Chip USB-to-USB Networking Solution FEATURES
* * * * * * * Smallest completely integrated solution in the market 32 pin TQFP Only requires a single crystal and small 16 byte serial EEPROM for full implementation Meets difficult suspend current of 500 uA for both hosts 2K data buffer for maximum speed transfer Greater than 5 Mbps data transfer rate Low power - Less than 100 mW power
OVERVIEW
The Cypress AN2720SC provides a single-chip solution for networking two or more computers via their USB ports. In a USB system, the PC acts as a host, which initiates all USB traffic. USB devices act as slaves, which respond to host requests. It is inherently incompatible to connect two PCs together via a simple USB cable, since a master (host) cannot talk to another master (host). A master can talk only to one or more slave devices. The AN2720SC overcomes this "peer-to-peer" incompatibility by providing two USB devices, one for each PC. Two independent Serial Interface Engines (SIE) exchange data through a 2 kilobyte FIFO. Thus, USB data transmitted by one computer is made available to the other computer through the AN2720SC. The connection is full duplex- data can be transferred in both directions simultaneously.
AN2720SC Block Diagram System Application
EZ-Link (AN2720SC)
APPLICATIONS AND MARKETS
The use of the AN2720SC and special network driver software provided by Cypress allows very simple and efficient networking between PCs. The "plug-and-play" nature of USB makes connecting two computers (even when powered) very simple. With the AN2720SC, simple networking can be provided in numerous form factors including: * USB standalone hubs * Computer monitors with USB hubs * Standalone USB cables * Port Replicators * WinCE Machines * Set-Top Boxes * Docking Stations * PC motherboards (particularly for laptops) Depending on the driver set used, the AN2720SC can perform the following functions: * USB networking * File transfer (including MAC to PC file sharing) * Windows CE synchronization * Printer sharing * Share internet connections (requires proxy or bridging software) * Multi-player gaming
SYSTEM DIAGRAM
VBUS
VBUS S I E
2 Kilobyte FIFO
Computer A
U S B
D+ DGND
S I E
D+ DGND
U S B
Computer B
AN2720SC
AN2720 Data Sheet Version 1.0
06/07/00
Page 2
EZ-Link (AN2720SC)
CHIP DETAILS
The AN2720 contains two slave interfaces that transfer data between through a 2-kilobyte FIFO. It also contains two 5V to 3.3V regulators to supply power to the chip and to the USB pullup resistor. Figure 2 of this document shows a functional block diagram of the AN2720. The AN2720 contains: ! Two 5V to 3.3V regulators, which deliver clean, regulated power to the chip and to the pullup resistor connected to the USB D+ line. These regulators are powered by the USB 5V line. ! Two USB transceivers, one for each computer. ! Two USB cores, each consisting of a Serial Interface Engine (SIE) and an intelligent machine that can respond to standard USB requests. These are the same enhanced SIE's used in Cypress' line of EZ-USB products. ! A 2-Kilobyte FIFO which is used to buffer multiple packets between computers to optimize data throughput. ! Control logic to manage transfer of USB data between the two SIEs. ! A single-crystal oscillator and PLL, shared by both SIE's.
SOFTWARE SUPPORT
Software is provided in two different configurations: Ethernet drivers or Ethernet plus bridging software. The Ethernet drivers run on Windows 95/98/2000 and are miniport device driver software which emulates a network interface connector. It manages the USB protocol and the PC-to-PC data flow. The EZ-Link Ethernet device driver is written to the NDIS (Network Driver Interface Specification) standard and provides a standard Windows interface to the resources of the hardware. To the end user, EZ-Link appears and behaves like an Ethernet card even though no physical network interface card is present. Thus, users can use standard Windows interface such as Windows Explorer, Network Neighborhood and standard file sharing security features. With this driver, users can use multiple EZ-Links to generate their own private mobile network, with access to other peripheral devices such as printers appearing as network peripherals. The Ethernet plus bridging drivers run on Windows 95/98/2000. In addition to the Ethernet connection capability between multiple EZ-Links, users can connect to corporate LANs using the PC that has both EZ-Link and a corporate Ethernet connection as a bridge device. With this capability, users have complete access to corporate LAN resources.
AN2720 Data Sheet Version 1.0
06/07/00
Page 3
EZ-Link (AN2720SC)
ADDITIONAL SOFTWARE UTILITIES
Unlike other Host-to-Host devices in the market, Cypress provides an entire suite of software utilities which enhance the end user experiences. Such utilities include: * Specialized Install procedure. The custom install procedure pioneered by Cypress allows immediate network operation without the need for the end user to access the Network Icon in the Control Panel. This makes it easy for "Instant Operation" without the need for the user to understand any networking jargon. Numerous article reviews rave over this feature. Make Disk Utility. In case an end user does not have the install CD-ROM in possession, the end user can still install the necessary drivers to a floppy disk using this Make Disk Utility. This allows the end user to continue to network to other computers without the need of the install CD-ROM. Electronic On-line Users Manual. This slick HTML electronic manual includes everything with regards to Networking operation in an easy-to-read format. Such Information includes Getting Started information, installation, various configurations, advanced operations and a background in Networking. EZ-Link Network Manager. While the user can use Windows Explorer and Network Neighborhood to navigate for data transfer and accessing other computers, it may take up to 5 minutes for the system to recognize all computers connected to EZ-Link. With the EZLink Network Manager, the user can access all computers connected to the EZ-Link private LAN immediately. The interface is intuitive and requires no manual for operation.
*
*
*
AN2720 Data Sheet Version 1.0
06/07/00
Page 4
EZ-Link (AN2720SC)
AN2720 ENDPOINTS
Figure below illustrates the AN2720 endpoints and how they are connected between two computers A and B.
(A) EP0
Control endpoints Status Interrupt
(B) EP0
(A) EP1
(B) EP1
(A) EP2 OUT Computer (A)
15 packet buffer (15 X 64 bytes)
(B) EP2 IN Computer (B)
(A) EP2 IN
15 packet buffer (15 X 64 bytes)
(B) EP2 OUT
(A) EP3 OUT
1 packet buffer (64 bytes)
(B) EP3 IN
(A) EP3 IN
1 packet buffer (64 bytes)
(B) EP3 OUT
AN2720 endpoints and FIFOS
Endpoint zero is the default CONTROL endpoints required by every USB device. Endpoint 1 is an INTERRUPT endpoint, useful for communicating with the PC driver. Endpoints 2 and 3 are used to transfer USB BULK data. Endpoint 2 has extensive buffering (15 packets of 64 bytes each) and is designed to transfer high-bandwidth data. Endpoint 3, with a single packet of buffering, can be used as a higher priority channel for driver communication. Endpoints 2 and 3 operate similarly to each other, differing only by the amount of buffering between the computers. Considering endpoint 2, when Computer (A) sends a packet over its endpoint 2 OUT, the packet is stored in the 15-packet FIFO. If Computer (B) does not send any IN tokens to its endpoint 2 (to retrieve a packet) by the time fifteen packets have been stored, the AN2720 NAKS the next OUT packet from Computer (A). This handshake is maintained by both endpoints 2 and 3, in both directions. When one side is unplugged, all packets are flushed from the FIFOS, and the AN2720 NAKS all IN and OUT tokens from the attached side.
AN2720 Data Sheet Version 1.0
06/07/00
Page 5
EZ-Link (AN2720SC)
USB CONFIGURATION
The AN2720 supports a single configuration, with one interface consisting of the five alternate settings shown in Table 1.
Table 1. AN2720 endpoints and interface alternate settings
Endpoints ep0 (8 Bytes) ep1in (8 Bytes) ep2in (64 Bytes) ep2out (64 Bytes) ep3in (64 Bytes) ep3out (64 Bytes)
Setting 0 Control X Bulk Bulk X X
Setting 1 Test Mode
Setting 2 Control intrpt (1mS) Bulk Bulk Bulk Bulk
Setting 3 Test Mode
Setting 4 Test Mode
Alternate setting 0 is intended to consume no fixed USB bandwidth, ensuring that the AN2720 will always be enumerated on the USB bus. Alternate setting 2 uses the USB bandwidth more efficiently, employing an interrupt endpoint for status notification. Alternate settings 1, 3 and 4 are diagnostic modes reserved by Cypress. Do not use these modes.
AN2720 Data Sheet Version 1.0
06/07/00
Page 6
EZ-Link (AN2720SC)
VID/PID/DID CONFIGURATION
Windows plug and play (PnP) uses the USB VID, PID and DID to select the driver for each device in the system. It is possible to have two 2720 chips attached to a host, but have different drivers loaded for them (for example, to create a CE-Link serial link emulator and an EZ-Link NDIS product as separate devices). The Manufacturing ID information is supplied from an EEPROM through the I2C port (SDADID1, SCLDID0). The I2C boot loader will check to make sure that an EEPROM exists and that the first byte in the EEPROM is 0xB0. If the boot loader finds that there is no EEPROM or that there is an EEPROM but the first byte is not 0xB0 then the VID/PID/DID will default to 0x0547, 0x2720, and 0x0000, respectively. If, however, there is an EEPROM and the first byte is 0xB0, then the boot loader will read the next six bytes to determine the custom VID/PID/DID: Byte Number 0 1 2 3 4 5 6 Value 0xB0 VID LSB VID MSB PID LSB PID MSB DID LSB DID MSB
These bytes are reported in bytes 8-13 of the device's response to a standard GET_DESCRIPTOR device request.
AN2720 Data Sheet Version 1.0
06/07/00
Page 7
EZ-Link (AN2720SC)
PINOUT
DMINUS-B
DMINUS-A
DPLUS-B
DPLUS-A
BCONN
ACONN
32
VSS NC RESERVED (GND) RESERVED (GND) AVSS XTALIN XTALOUT AVDD
VDD
VSS
31
30
29
28
27
26
25 24 23
MAIN3V MAIN5V RESERVED (GND) PULP3V PULP5V RESERVED (GND) NC VSS
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16
EZ-Link AN2720SC 32 TQFP
22 21 20 19 18 17
RESERVED (GND)
RESERVED (GND)
RESERVED (GND)
RESET#
VSS
SDA
SCL
Figure 1. AN2720SC pinout
AN2720 Data Sheet Version 1.0
06/07/00
NC
Page 8
EZ-Link (AN2720SC)
PIN DESCRIPTIONS
Signal name Pin # VSS 1 NC 2 Reserved Reserved AVSS XTALIN 3 4 5 6 Type GROUND INPUT INPUT GROUND INPUT Driver Description Ground Reserved for future use. Must remain unconnected Connect to Ground Connect to Ground Ground Connect this signal to a 12Mhz series resonant, fundamental mode crystal and 22-33 pF capacitor to GND. Data-rate tolerance is 0.25% (2,500ppm) under all conditions. Connect this signal to a 12Mhz series resonant, fundamental mode crystal and 22-33 pF capacitor to GND. Data-rate tolerance is 0.25% (2,500ppm) under all conditions. Connect to MAIN3V and decoupling caps. Ground Active low reset input Connect to Ground Connect to Ground Connect to Ground Data line for I2C bus. Requires external 2.2K pullup. Clock line for I2C bus. Requires external 2.2K pullup. Reserved - No connect Ground No connect Connect to Ground Connect to B-side VBUS. Provides 3V for B-side D+ pullup resistor. See the example circuit for details on the use of this pin.
SPECIAL
XTALOUT
7
OUTPUT
SPECIAL
AVDD VSS RESET# Reserved Reserved Reserved SDA SCL NC VSS NC Reserved PULP5V PULP3V
8 9 10 11 12 13 14 15 16 17 18 19 20 21
Analog POWER GROUND INPUT INPUT INPUT INPUT IO IO Reserved GROUND Reserved INPUT INPUT OUTPUT
CMOS input
2mA CMOS bidir 2mA CMOS bidir Reserved Reserved Reserved Regulator power input Regulator power output
AN2720 Data Sheet Version 1.0
06/07/00
Page 9
EZ-Link (AN2720SC)
Signal name Pin # Reserved 22 MAIN5V 23 MAIN3V 24 Type INPUT INPUT OUTPUT Driver SPECIAL Regulator power input Regulator output Description Connect to ground. 5V input to integrated regulator. Connect to A side VBUS. 3V output from integrated regulator. Can be used as a 3.3V power supply and as 3.3v source for the 1.5K USB pullup. Ground D- pin for A side USB connection D+ pin for A side USB connection Indicates to the chip that the 5V is present on the A side USB connector. Connect directly to A side VBUS. Indicates to the chip that the 5V is present on the B-side USB connector. Connect directly to Bside VBUS. D- pin for B side USB connection D+ pin for B side USB connection Input power for the digital portion of the chip. Connect to the 3.3V net w/ decoupling.
VSS DMINUSA DPLUSA ACONN
25 26 27 28
GROUND IO IO Input
SPECIAL SPECIAL CMOS input
BCONN
29
Input
CMOS input
DMINUSB DPLUSB VDD
30 31 32
IO IO POWER
SPECIAL SPECIAL
AC/DC PARAMETERS
ABSOLUTE MAXIMUM RATINGS
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-65 C to +150 C Ambient Temperature Under Bias . . . . . . . . . . . . . . . . . . . -40 C to +85 C 3.3 V Supply Voltage to Ground Potential . . . . . . . . . . . . . . -0.5V to +4.0 V 5 V Supply Voltage to Ground Potential . . . . . . . . . . . . . . -0.5V to +5.8 V DC Input Voltage to Any Pin . . . . . . . . . . . . . . . . . . . . . . . .-0.5V to +5.8 V
AN2720 Data Sheet Version 1.0
06/07/00
Page 10
EZ-Link (AN2720SC)
OPERATING CONDITIONS
Ta (Ambient Temperature Under Bias) . . . . . . . . . . . . . . . . . 0 C to +70 C 5V Supply Voltage (VBUS) . . . . . . . . . . . . . . . . . . . . . . . . +4.4V to +5.25 V Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +3.0V to +3.6 V Ground Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V FOSC (Oscillator or Crystal Frequency). . .. . .. . . . . . . . .. .12 MHz +/- 0.25%
DC CHARACTERISTICS
Symbol VCC VIH VIL II VOH VOL CIN ISUSP Parameter Supply Voltage Input High Voltage Input Low Voltage Input Leakage Current Output Voltage High Output Low Voltage Input Pin Capacitance Suspend Current Condition Min 3.0 2 -.5 2.4 .8 10 250 Max 3.6 5.25 .8 + 10 Unit V V V A V V pF A Add 220 A for 1.5K pullup resistor. Notes
0< VIN < VCC IOUT = 1.6 ma IOUT = -1.6 ma Using internal regulator
ICC IOUT MAIN3 VOUT
Supply Current Regulator output current Regulator output voltage
Transferring data, connected to USB
30 .200 3.3 50 5
mA mA V Regulator will supply 5V for less than 200ms at initial startup.
AN2720 Data Sheet Version 1.0
06/07/00
Page 11
EZ-Link (AN2720SC)
PACKAGE DRAWING
9.00 BSC 7.00 BSC
SQ.
32
25
1
24
0.80 BSC.
32 TQFP
8
17
9
16 8 Places 11/13o
1.60 MAX See Lead Detail
0.30/0.45
With Lead Finish 0.09/ 0.16 Base Metal
0.09/ 0.20
~
0.30/0.40
Figure 2. Package information
AN2720 Data Sheet Version 1.0
04/27/01
Page 12
EZ-Link (AN2720SC)
Figure 3. Package detail
Detail
0o MIN.
0.08/0.20 R. 1.35/1.45 Datum Plane -H0.25 Gauge Plane
0.05/0.15
0.08 R. MIN. 0 - 7o 0.20 MIN. L. 1.00 REF.
0.30/0.45
Lead Sides
0.80 BSC/2
Lead Sides
All Dimensions in MM.
AN2720 Data Sheet Version 1.0
04/27/01
Page 13
EZ-Link (AN2720SC)
BOARD SCHEMATIC
AN2720 Data Sheet Version 1.0
04/27/01
Page 14
EZ-Link (AN2720SC)
SCHEMATIC NOTES
The AN2720SC includes two onboard regulators. The USB suspend current specification only permits a device to draw 500 uA in the suspend mode. The pullup resistor on D+ draws 200 uA by itself, without any assistance from the AN2720SC. The second regulator allows each side to have its own 500 uA suspend budget. The transistor and diode configuration on the BDPLUS pullup is used for power management. While only one side is connected, it is important not draw power from the host side even though it is physically connected. To simplify power management, we have assumed power is expected to always come from the A side of the chip. So when the A side is not connected and thus not receiving power, the B side must be disconnected from the host power source since the peripheral is not in use. The pullup on the B side is switchd by the AVBUS line via the transistor, electrically disconnecting the B side when AVBUS is removed. The "MNT" of the "MNT5" and "MNT6" in the JP1s USB-B represent mounting tabs on the USB B connector. They are on the schematic because they must be attached to the ground plane. The schematic proposed will work for any number configurations, including the use of 2 B connectors or a complete cable with 2 A side connectors on each side of the chip. The 24LC00 device is used for the VID and PID of the EZ-Link device. While we have included the most space efficient one in the schematic, any version will suffice. The SN75240 is a USB surge suppressor from Texas Instruments. This surge suppressor is optional, but it does provide up to 8 KV of ESD protection. Since the USB interface has wires exposed to the outside world, some level of ESD immunity higher than the 2KV level inherent to the AN2720SC is recommended. Should there be difficulties in passing the difficult EMI standards, a white paper at the Intel website should help guide the developer in resolving EMI problems. The white paper explores the variety of different methods of EMI reduction. For reference, the URL is http://developer.intel.com/design/USB/papers/EMI_APPS.HTM.
AN2720 Data Sheet Version 1.0
04/27/01
Page 15
EZ-Link (AN2720SC)
ORDERING PART NUMBERS
Cypress Part Number AN2720SC-01 AN2720SC-02 Description AN2720SC plus Ethernet software AN2720SC plus Ethernet and bridging software
DOCUMENTATION REVISION HISTORY
Revision Initial 0.9 0.91 0.92 0.95 0.97 1.0 1.1 Date 9/20/98 9/29/98 10/06/98 10/8/98 11/10/98 2/12/99 5/15/99 6/07/00 Changes Initial release. No revision information saved Updated based on Engineering feedback Updated package drawing Slight corrections based on more Engineering feedback Updated block diagram, included part numbers and s/w section Updated schematic. Included schematic notes. Added more detailed description of the crystal requirements Changed from Anchor Chips to Cypress and other minor changes
Cypress Semiconductor Corporation 3901 North First Street * San Jose, CA 95134 408-943-2600
www.cypress.com
AN2720 Data Sheet Version 1.0
04/27/01
Page 16

▲Up To Search▲

Price & Availability of AN2720S

	To Download AN2720S Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .